If you have ever tried to load heavy equipment into the back of your truck, you know the value of a good loading ramp. Aluminum loading ramps are available at auto parts stores or home centers at considerable expense.

However, if you are on a budget, constructing a wooden loading ramp may be just the ticket if you need a way to load your motorcycle, garden tractor, wheelchair or construction equipment into your vehicle from ground level. Place the notched end of a ramp plate on one end of the lumber.

Use the ramp plate mounting holes as a template and make pencil marks through the mounting holes onto the surface of the lumber. Remove the ramp plate and set it aside. Drill through the lumber on the pencil marks.

diy wooden ramp

Place the ramp plate back into position, making sure to line up the mounting holes with the holes drilled into the lumber. Drive the carriage bolts in with a hammer until they are fully seated. Turn the entire assembly over so the underside of the lumber is facing upward. Place washers and lock nuts on the threaded ends of the carriage bolts that protrude through the under side of the lumber. Tighten the lock nuts with an adjustable wrench in a clockwise direction.

Place the ramp assembly into position on the edge of your pickup bed or tailgate or any other loading surface being used so that the lip of the ramp plate sits on the supporting surface.

Drive 0. Be aware these screws are used as pins to hold the ramp from sliding while it is in use. Use the ramp as desired and remove the self tapping screws in a counterclockwise direction with an adjustable wrench when you wish to remove the ramp.

Make an additional loading ramp using the above instructions if you need a pair of ramps. Step 1 Place a 2-inch x 8-inch x 8-foot piece of lumber across two sawhorses.

Step 2 Place the notched end of a ramp plate on one end of the lumber.

How to Build a Shed Ramp the Right Way

Step 5 Turn the entire assembly over so the underside of the lumber is facing upward. Step 6 Place washers and lock nuts on the threaded ends of the carriage bolts that protrude through the under side of the lumber.

Step 7 Place the ramp assembly into position on the edge of your pickup bed or tailgate or any other loading surface being used so that the lip of the ramp plate sits on the supporting surface.Making a ramp tops is one of the best DIY projects you can execute and there are various types of ramp plans you can create to improve functionality within your home, we have compiled 16 free easy to build DIY ramps plans to make your home more attractive and accessible.

There are steps to guide you on how to build a ramp to enable you to get underneath your car quickly, a wheelchair ramp or shed ramp for more accessibility to and a skateboard ramps to provide a fun-filled skateboarding experience right in your home. Basic supplies required. If you have the budget, you can buy most of these tools, as you would be using them for other diy projects.

Otherwise, lookout for where you can borrow some of these. Building a wheelchair ramp would be a fantastic project to carry out. This ramp can go a long way in helping someone with mobility challenges live independently and can be made of wood or all aluminum.

You can get already formed ramp material wooden or Prefabricated aluminumand then assemble it yourself. When making this ramp, you need first to create a sketch of your ramp considering the measure of the width, landing size and location.

Ramps for a Low Car

Measure the distance between the thresholds to the ground and adjust the length and slope of the ramp to fit your yard. Then start building.

diy wooden ramp

Moving a wheelchair into homes, vehicles and shops could be hectic as the entrance might be steep. A portable wheelchair ramp becomes the ideal solution to ease movement in and out of these places. When building these ramp plans, always bear in mind the measurements of the available space.

Father Son project DIY Car Ramps

You can attach handles to the ramp for comfortable carriage. Make your home easily accessible to people with movement challenges with this classic DIY project. Handicap ramps are easy to create and a great DIY project to embark on. First, you have to measure your space and then sketch your ramp design.

Check to ensure the frame is sturdy, then add a few pressure treated wood shims in areas where needed, before attaching the structure to the building with nails. Create support for the ramp, by cutting woods that measure from the top of the landing to the concrete base and nailing them to the side of the ramp. This mini ramp plan provides a gentler and less stressful way of entering or leaving their home for them.

This is amongst the most straightforward DIY projects you can start right away. However, you might want to ensure building a wheelchair ramp complies with local building requirements and its created to meet the specific needs of the occupant.

The wheelchair ramp should be formed according to the measurement of the entrance point of the home. To make it safe and sturdy, hardwood is used and its coated with stain to ensure durability. The design of this diy ramp is very straightforward.

First, cut the wood to the required dimension and get the fillets done and edge sloped. Get the plank smoothened using a hand planer ; you can take it to a carpenter to do this.

Next, attach the planks to each other by applying the adhesive at the base of each plank and then stacking them one above the other. After that, you can then use a Philip-head to screw it together.A portable ramp is a great thing to have if you want to move materials or a wheelchair up and down an incline. There are different types of ramps available. Modular ramps are mostly stationary ramps that remain in one place.

Portable ramps are ramps that can be moved quickly to wherever they are needed. Telescopic ramps are ramps that close down and fold away when not in use. The threshold ramp is a small ramp used to bridge small variations in the floor level. And finally, there is the permanent ramp [source: Independent Living ]. We will now show you how to build a portable ramp, though note that because this ramp is constructed from plywood, it should not be used when damp or wet, nor should it be used for an extended period of time, as the plywood might become warped.

It's a portable, temporary project. Materials needed: Advertisement. Saw the rectangle along the diagonal. You now have two triangles. Cut five pieces of 2-by-4s into inch Stand the two triangles on the inch 61 centimeter side, parallel to each other, 28 inches Attach the two triangular pieces to each other by screwing the five 2-by-4s into the triangles on the sloping side that is facing up.

The 2-by-4s should span the space between the triangles. The 2-by-4s should be equidistant from each other. Cut another piece of 2-by-4 into a inch Screw this board to the bottom of the two pieces of plywood on the short straight side. Screw the rectangle onto the ramp frame. The inch Place a screw every 10 inches Make sure you screw the plywood into the 2-by-4s too.

The rectangle will overlap on both sides. Paint and varnish the whole ramp [Source: Do It Yourself]. Related Content " ". How to Rewire a Lamp in 9 Steps. How to Repair Floors. Art Shades.People often find it difficult for their old parents or any disabled family member or anyone who suffers from mobility challenges to enter the house — especially when the house is at a certain height from the ground — while the only way to go inside the house is stairs.

In such cases, making a ramp that is safe and helpful can make the physically disabled person feel independent. A hired contractor can construct it in a day or two. Nonetheless, you can install it on your own too if you are equipped with a miter saw router, drill, level, and have some basic carpentry skills. Permanent installation of ramps needs frost-proof footings to prevent frost heaving-caused interference with the door in the winter, whereas, treated plywood pads are enough for temporary use of the ramp.

Long spans generally give adjustment problems, and if the changes are made in the original design, the adjustment becomes more complicated. So, it is better to go with building individual modules and clamp them together at the vertical supports.

You can also disassemble them and make a new design if needed. If the ramp is built on a straight line, using the Pythagoras formula, the ramp length equates to the square-root of the sum of the squared rise height and the squared distance of end-point from the threshold. The ramp must have at least inches clear side-to-side space and a maximum 36 inches spacing from the top of the handrails to the ramp floor. L-shaped ramp with a landing or a U-shaped ramp with a landing depends on the configuration of your home.

The key point is, discuss with an architect before starting and make sure you have all the approvals needed for the ramp and you use only the treated timber. Finally, an efficient and beautiful wooden wheelchair ramp will be ready which makes the lifestyles of the physically challenged in mobilitymore comfortable and independent to a great extent. Your email address will not be published.

Save my name, email, and website in this browser for the next time I comment. Skip to content People often find it difficult for their old parents or any disabled family member or anyone who suffers from mobility challenges to enter the house — especially when the house is at a certain height from the ground — while the only way to go inside the house is stairs.

How to Make a Wooden Loading Ramp

Process of Making a Wooden Wheelchair Ramp Measurements The very first step is to estimate the distance from the doorstep to the ground. Make sure the exterior door you are selecting has sufficient space in the front to accommodate a ramp of slope, as this ratio is most suitable.

But if you do not have enough space on the lawn, go for the ramp with a slightly steeper grade of about or Permission If the ramp is above 30 inches from the ground, you might need a permit. Footings Permanent installation of ramps needs frost-proof footings to prevent frost heaving-caused interference with the door in the winter, whereas, treated plywood pads are enough for temporary use of the ramp.

Switch to Modules Instead of Long Spans Long spans generally give adjustment problems, and if the changes are made in the original design, the adjustment becomes more complicated.Make your deck more accessible by installing a ramp or flat stairs.

DIY Wheelchair Ramps

Here's how to do it. An access ramp could be viewed either as an angled deck or flat stairs, and it shares construction techniques with both.

diy wooden ramp

Place the ramp for the most convenient and unrestricted access to the deck. Keep the maximum pitch the number of feet the ramp rises for every foot of horizontal run to 1 in 12, and if possible, build it 42 or 48 inches wide. The minimum width is 36 inches. Have the building inspector review your deck ramp plans before starting construction on the project.

Construct a single-tiered ramp—one whose entire rise is on a single stringer. Or, to build longer ramps, set posts on footings at equal intervals along both sides of the run.

Mark the angle of descent on the posts, and cut and install stringers with angled ends. Install handrails on ramps and landings. You'll need to remove sod and install landscape fabric and gravel before you begin. Learn how to build a ramp for a deck with our step-by-step instructions, below. Measure the rise of the ramp and adjust the run to comply with pitch requirements.

Drive stakes at the location of the landing pad. Lay out the landing pad with a sheet of plywood or batterboards. Remove the sod; excavate, form, and pour the landing pad. Spread landscape fabric and gravel on the site, then lay out the stringers. This notch will fit over a cleat fastened to the landing pad. Cut one stringer and use it as a template for the others. Cut a pressure-treated 1x6 to the outside width of the ramp.

Then set your circular saw to cut a 5-degree bevel on one edge of the 1x6. When the concrete is cured, mark the stringer positions on the joists and fasten the stringers to the joist.

Square the whole assembly to the deck and drill locator holes into the pad with a masonry bit. Remove the cleat, drill holes for the studs, epoxy them in place, and reinstall the cleat with nuts and washers. Cut the decking to length allowing a 1-inch overhang, and attach it to the stringers.

Space the boards with a spacing jig. To ease the transition between the pad and the ramp, brush a latex bonding agent on the existing concrete and trowel on a 6- to 8-inch-wide transition strip at the bottom edge of the decking.Size and slope. Along with slope and size, there are a few other factors needed when learning how to build a shed ramp. It is also imperative that you plan the slope well and consider what type of equipment will be used on the shed ramp.

Most require an 8 to 1-inch slope. Besides building codes on how to build a shed ramp, also research other codes at your local city office.

diy wooden ramp

Just one more thing to think about when considering how to build a shed ramp. To prevent this, use rubberized flooring or anti-slip paint can help decrease this risk of falling on your shed ram p.

Include this in your shed ramp plans so that you will not forget about any of these shed ramp tips. Just like when you use safety glasses around power tools, your new storage shed ramp needs to fit the needs of your machines you will be storing in the shed.

But as most permanent storage sheds are placed on a foundation pad or footing, you get a level difference of 9 to 14 inches above the ground. Hence, building a shed ramp is essential when you need to get heavy garden machinery and riding movers in and out of the storage shed.

It makes loading and unloading of heavy equipment from your shed or garage safe and easy thereby reducing the risk of accidents. Before you can have your storage shed placed, you prepare a solid leveled base including gravel or crushed stone with either treated wood foundations or concrete foundation blocks. For large sheds, you require strong foundations to uniformly transfer the load. So, due to the level difference of the floor level with the adjacent ground level you have to build a storage shed ramp of suitable length and slope provision for safe and stress-free movement of heavy equipment in and out of the garage.

Choosing the length and slope of the shed ramp is a very important part of your shed planning for getting the maximum benefit out of it. Whether your using shed ramp plans or have your own shed ramp ideas, an ideal shed ramp will have a shallow slope and excess length for ease of use. But you have to make sure that there is sufficient space available in front of the shed. The slope and length required are governed by the height from the external ground level to the shed floor.

Regarding the slope selection here are some recommendations for building a shed ramp:. For public ramps, the steepest slope allowed is which means one-inch rise for every 12 inches horizontally. This slope is governed by the ease of use for wheelchair users. For general public building, the recommended maximum slope is which means one-inch rise for every 8 inches horizontally.These wood ramps are primarily meant for residential construction projects. Because they are made from wood, they are far less expensive than aluminum or custom contractor-built ramps.

With my kit, nearly anyone can easily build a wood wheelchair ramp for easy access whether you live in the Kansas City area or throughout the U. My wheelchair ramp kits are an affordable permanent or temporary solution. No measuring or cutting is necessary because this is an assembly project. As the name suggests, almost anyone can build one of my ramps. You can build a residential straight ramp for up to foot long in 2 hours. Contact me on how one person can build a 'sectional' wheelchair ramp to address needs of nearly any length.

I know the right questions to ask and can show you how to build affordable wheelchair ramps for home to achieve the proper slope for your unique situation before you purchase anything.

I invite you to take advantage of my residential DIY wheelchair ramps expertise for free with no obligation, especially if you live in the Kansas City or Overland Park, Kansas area. Minimal DIY Skills needed.

Know how to use an electric drill? You can build a 'kit' ramp. Read actual customer reviews located under the About tab. Free design and construction advice for your specific patient and property situation. No obligation! I provide telephone support guidance to assist in your design and how to build DIY wheelchair ramps. If you live in greater Kansas City or Overland Park area, I will be glad to go onsite and advise the best ramp design for your situation.


thoughts on “Diy wooden ramp”

Leave a Reply

Your email address will not be published. Required fields are marked *